1/16 DIN Limit Controller

CN6221 Series

Se Alt Models Below

PLACE ORDER

Dual Display
Universal Input
High or Low Limit
Digital Input for Remote Reset
RS485 Communications (Optional)
Alarms (Optional)
Retransmission Output (Optional)
FM, UL and CSA Approved

Controllere, målere og koblingsanordninger - Vis relaterede produkter

Beskrivelse

The CN6221 Series is an FM approved limit controller that can be configured either as a high limit or as a low limit controller. The CN6221 features universal input, Optional 2 alarm outputs, Optional retransmission output, a timer to count the total time the setpoint is exceeded, and a register to retain the maximum. The RS485 communication interface is available as an option.

Input Type		Range (°C)	Range (°F)
Thermocouple	K	-270 to 1370	-300 to 2500
		0 to 600	32 to 999.9
		0 to 400	32 to 750
		-199.9 to 200	-300 to 400
	J	-199.9 to 999.9	-300 to 2100
	T	-199.9 to 400	-300 to 750
	E	-199.9 to 999.9	-300 to 1800
	R	0 to 1700	32 to 3100
	S	0 to 1700	32 to 3100
	B	0 to 1800	32 to 3200
	N	-200 to 1300	-300 to 2400
	L	-199.9 to 900	-300 to 1600
	U	-199.9 to 400	-300 to 750
	Platinel 2	0 to 1390	32 to 2500
RTD	Pt100	-199.9 to 850	-199.9 to 999.9
		0 to 400	32 to 750
		-199.9 to 200	-300 to 400
		-19.9 to 99.9	-199.9 to 999.9
	JPt100	-199.9 to 500	–
DC Voltage	0 to 100 mV	0 to 100	–
	0 to 5 V	0 to 5	–
	1 to 5 V	1 to 5	–
	0 to 10 V	0 to 10	–

SPECIFICATIONS
Power Supply
Voltage: 100 to 240 Vac (±10%),
Frequency: 50 or 60 Hz
Maximum Power Consumption: 8 Va max (4 W max)
Memory: Non-volatile memory
Withstanding Voltage (Between Primary and Secondary Terminals): 1500 Vac for 1 min (see Note1)
Insulation Resistance (Between Primary and Secondary Terminals): 20 MΩ or more at 500 Vdc (see Note 1)
Note 1: The primary terminals are the power supply terminals and relay output terminals. The secondary terminals are the analog input and output terminals, the voltage pulse output terminals, and the contact input terminals.

Contact Input
Function: Resetting "exceeded status"
Input: 1 point
Type: Non-voltage contact or transistor contact
Contact Capacity: At least 12 V/10 mA
On/Off Judgment: On state for 1 kΩ or less; off state for 20 kΩ or greater

Measured Value (PV)
Input: 1 point
    Type: Universal
    Accuracy (At 23 ±2°C Ambient Temperature):
    Thermocouple: ±2°C ±1digit
       At -200 to -100°C: ±4°C
       At -100 to 0°C: ±3°C
       Types R and S: ±5°C [±9°C for 0 to 500°C (X to X°F)]
       Type B: ±9°C (accuracy is not guaranteed for 0 to 400°C)
    RTD: ±1°C ±1digit
    Voltage (mV, V): ±0.3% ±1digit
Sampling Period for Measured Value Input: 500 ms
Burn-Out Detection: Functions for thermocouple or RTD input (burn-out upscale only; cannot be switched off)
Input Resistance: 1 MΩ or greater for thermocouple or DC mV inputs; approx 1 MΩ for DC V input
Maximum Allowable Signal Source Resistance: 250 Ω for thermocouple or DC mV input; 2 kΩ for DC V input
Maximum Allowable Wiring Resistance for RTD Input: 10 Ω/wire (resistance values of 3 wires must be the same)
Allowable Input Voltage: ±10 Vdc for thermocouple or DC mV input; ±20 Vdc for DC V input
Noise Rejection Ratio:
    Normal Mode Noise: Minimum 40 dB (50/60 Hz)
    Common Mode Noise: Minimum 120 dB (90 dB for DC V input)
Reference Juction Error Compensation: ±1.5°C (at 15 to 35°C), ±2.0°C (at 0 to 50°C)
The reference junction compensation cannot be switched off
Applicable Standards: RTD, Thermocouple, JIS/IEC/DIN (ITS90)

Til bestilling(Angiv modelnummer)

Andre har købt: Du kan klikke på dette ikon og få vist en liste over produkter, som andre har købt sammen med denne model.

Vare nummer/Desc.

Antal

Beskrivelse

CN6221-R

Kontakt salgsafdelingen

Beholdning:

Limit controller, single relay output

Accessories (Field installable)

CNQUENCHARC

€51,23

Beholdning: På lager

Noise suppression kit, 110 to 230 Vac

† All amounts shown in EUR
Noter: Comes with complete operator’s manual.

Delnummerberegner

Build Your Part Number Below

	(1)
CN6221-R

Beskrivelse af tilvalg:

(1) Option1 select from:
Nothing(leave field blank) for none
-AL for Dual alarms
-PV for 4 to 20 mA retransmission output
-C4 for RS485 communications (Only one option can be ordered)
-DI for Digital input switching(Only one option can be ordered)

Noter: Ikke alle kombinationer er nødvendigvis gyldige. Se specifikationerne for gyldige delnumre.