1/16 DIN Autotune Temperature Controllers - Discontinued

CN63100 Series

1/16 DIN Autotune Temperature Controllers

Se Alt Models Below

PLACE ORDER

PID Control With Reduced Overshoot
On-Demand Auto-Tuning of PID Control Settings
NEMA 4X (IP65) Bezel
Dual LED Displays for Simultaneous Indication of Temperature and Setpoint
Status Indicators for Outputs and Control Modes
Thermocouple or RTD Inputs
Optional Dual Alarm Inputs
Optional Linear DC Output, Control or Retransmission (0 to 10 V, 0/4 to 20 mA)
Manual/Automatic Control Modes
Setpoint Ramping For Process Startup
Sensor Error Compensation (Offset) and Break Detection
Heating and Optional Cooling Outputs
Parameter Security Via Programmable Lockouts
Field-Replaceable Output Board
Optional RS485 Serial Communications

Beskrivelse

The CN63100 series has been discontinued. Please see the CND3 Series as a possible alternative or upgrade.

The CN63100 Series Controller accepts signals from a variety of temperature sensors (thermocouple or RTD), precisely displays the process temperature, and provides an accurate output control signal (time proportional or linear DC) to maintain the process at the desired temperature. The controller comprehensive yet simple programming allows it to meet a wide variety of application requirements. The controller operates in the PID control mode for both heating and cooling, with on-demand auto-tune, which will establish the tuning constants. The PID tuning constants may be fine-tuned by the operator at any time and then locked-out from further modification. The controller employs a unique overshoot suppression feature, which allows the quickest response without excessive overshoot. The unit can be transferred to operate in the manual mode, providing the operator with direct control of the output. The controller may also be programmed to operate in the “ON/OFF” control mode with adjustable hysteresis. A second setpoint is available on select models to allow quick selection of a different setpoint setting. Dual 4-digit displays allow viewing of the process temperature and setpoint simultaneously. Front panel indicators inform the operator of the controller and output status. On many models the main control output and the alarm outputs are field replaceable. Optional alarm(s) can be configured to activate according to a variety of actions (absolute high or low, deviation high or low, band in or out, with adjustable hysteresis. A standby feature suppresses the alarm during power-up until the temperature stabilizes outside the alarm region. The second alarm can be configured as a secondary PID output (heat/cool applications).

Til bestilling(Angiv modelnummer)

Vare nummer/Desc.

Antal

Beskrivelse

Standard Power Models, 85 to 250 Vac, 50 to 60 Hz, 8 VA Max

CN63100-R1

Kontakt salgsafdelingen

Beholdning:

Single output, relay

CN63100-R1-R2-AL

Kontakt salgsafdelingen

Beholdning:

Dual output, relay/relay, alarm

CN63100-R1-R2-AL-RSP

Kontakt salgsafdelingen

Beholdning:

Dual output, relay/relay, alarm, remote setpoint

CN63100-DC1

Kontakt salgsafdelingen

Beholdning:

Single output, DC pulse

CN63100-DC1-R2-AL

Kontakt salgsafdelingen

Beholdning:

Dual output, DC pulse/relay, alarm

CN63100-R1-R2-AL-C4

Kontakt salgsafdelingen

Beholdning:

Dual output, relay/relay, alarm, RS485

CN63100-DC1-R2-AL-C4

Kontakt salgsafdelingen

Beholdning:

Dual output, DC pulse/relay, alarm, RS485

CN63100-R1-R2-F3

Kontakt salgsafdelingen

Beholdning:

Dual output, relay/relay, analog control or re-transmission

CN63100-R1-R2-F3-RSP

Kontakt salgsafdelingen

Beholdning:

Dual output, relay/relay, analog control or re-transmission, remote setpoint

CN63100-R1-R2-F3-C4

Kontakt salgsafdelingen

Beholdning:

Dual output, relay/relay, analog control or re-transmission, RS485

Low-Voltage Models, 18 to 36 Vdc; 7 W

CN63100-R1-LV

Kontakt salgsafdelingen

Beholdning:

Single output, relay

CN63100-R1-R2-AL-LV

Kontakt salgsafdelingen

Beholdning:

Dual output, relay/relay, alarm

CN63100-R1-R2-AL-RSP-LV

Kontakt salgsafdelingen

Beholdning:

Dual output, relay/relay, alarm, remote setpoint

CN63100-DC1-LV

Kontakt salgsafdelingen

Beholdning:

Single output, DC pulse

CN63100-DC1-R2-AL-LV

Kontakt salgsafdelingen

Beholdning:

Dual output, DC pulse/relay, alarm

CN63100-R1-R2-AL-C4-LV

Kontakt salgsafdelingen

Beholdning:

Dual output, relay/relay, alarm, RS485

CN63100-DC1-R2-AL-C4-LV

Kontakt salgsafdelingen

Beholdning:

Dual output, DC pulse/relay, alarm, RS485

CN63100-R1-R2-F3-LV

Kontakt salgsafdelingen

Beholdning:

Dual output, relay/relay, analog control or re-transmission

CN63100-R1-R2-F3-RSP-LV

Kontakt salgsafdelingen

Beholdning:

Dual output, relay/relay, analog control or re-transmission, remote setpoint

CN63100-R1-R2-F3-C4-LV

Kontakt salgsafdelingen

Beholdning:

Dual output, relay/relay, analog control or re-transmission, RS485

Accessories (Field-Installable)

CN6-48100

Kontakt salgsafdelingen

Beholdning:

Single relay output module

CN6-48111

€112,75

Beholdning: 1 uge

Dual relay/relay output module

CN6-48200

Kontakt salgsafdelingen

Beholdning:

Single DC pulse output module

CN6-48211

Kontakt salgsafdelingen

Beholdning:

Dual output, DC pulse/relay output module

CN6-RBDLA210

Kontakt salgsafdelingen

Beholdning:

Output module, single output, Form-C relay, 1 alarm

† All amounts shown in EUR
Noter: Comes with complete operator’s manual.
For “-C4” RS485 option, software is a free download from omega.com.