Cookies på Omegas websteder
Vi anvender cookies på vores websted. Disse cookies er afgørende for, at webstedet kan fungere korrekt.
Hvis du fortsætter uden at ændre dine indstillinger, antager vi, at du gerne vil modtage alle de cookies, der anvendes på dette websted. Du finder flere oplysninger om cookies ved at klikke her
Luk
Kurv  |  Kontakt  | 
GRATIS TELEFON (Kun Danmark. Alle opkald besvares på engelsk) 80 25 14 43
INTERNATIONAL(+45) 80 25 14 43
Layer N Banner

Ball Bearing Gas Turbine Flow meters with Male NPT Fittings

FTB-930

Gas Turbine meters | FTB-930

Gas Turbine meters

Se Alt Models Below

1 year warranty
  • Gas turbine meter with ±1% of Reading Accuracy
  • Ball Bearing Design for Economy
  • 440C Bearing Retainers for Durability
  • Ball Bearings Field Replaceable Without Loss of Calibration
  • Deflector Cones Stabilize Low Mass Rotor for Increased Bearing Life
  • NIST Certificate Supplied Standard
Flowmetre med turbine og skovlhjul - Vis relaterede produkter

Beskrivelse

Click on this link if you need more information about a Flow meter.

The OMEGA™ turbine gas meter of the FTB-930 & FTB-940 have male NPT end fittings for easy connections. They are suitable for use with gases with a minimum density of 0.025 lb/ft 3 (air at STP is 0.0752 lb/ft 3 ).These units come supplied with a mating 2-wire connector and can be supplied with integrally mounted FLSC-60 Series signal conditioners to provide 4-20 mA, 0-5 V, or amplified pulse outputs. These turbine gas meters are intended for clean service only; where there is any doubt about the fluid, strainers are recommended.

OMEGA™ precision turbine gas flowmeters are designed to measure actual cubic feet or actual volume passing through the meter. Before sizing a flowmeter, it is necessary to convert flow units (i.e., SCFM, LPM, etc.) to actual units. To convert to actual measured volume (ACFM) from standard volume (SCFM), use the following formula:
ACFM = SCFM x 14.7/Pa x Ta/530
where:
ACFM = Actual cubic feet per minute of measured gas flow
SCFM = Standard cubic feet per minute gas flow
Pa = Operating pressure (psia) in = (psig + 14.7)
Ta = Temperature in degrees, Rankine = (°F + 460)


SPECIFICATIONS
Accuracy: ±1.0% of reading
Repeatability: ±0.25%
Materials of Construction:
Body: 304/316 stainless steel
Rotor: 17-4 PH SS
Bearings: 440C stainless steel
Output: 30 mV p-p sinewave min.
Til bestilling(Angiv modelnummer)
Vare nummer/Desc.
Antal 
Beskrivelse
FTB-942
Kontakt salgsafdelingen    
Beholdning: 
 
 
75-1200 Max Linear Range (ACFM); 4 End Connections MNPT (in)
Accessories
PSU-24V-UNIVERSAL
Kontakt salgsafdelingen    
Beholdning: 
 
 
24V 0.75A regulated dc Power supply. 90-260 Vac 1.8 m lead with stripped ends. With International plugs
DPF20-HV-R1-R1
327,30
Beholdning: 8 uger 
 
6 digit, 1/8 DIN panel meter for Rate or Total, 85 to 260 Vac powered, with dual relay outputs
All amounts shown in EUR
Noter: Comes complete with operator’s manual and NIST Certificate for air.

To order turbine gas meters with integral signal conditioners, specify model as a system such as : SYS/FTB-932/FLSC-62A. Omega will scale the signal conditioner with the appropriate calibration information from the turbine meter specified.

No other calibrations are available.

Compatible Meters: DPF701, DPF402, DPF70 with FLSC-AMP, DPF10, DPF500, FC20, 21, 22

Contact Flow Engineering Dept


Ordering Example:  (1) DPF702 1/8 DIN Panel Meter for Rate or Total, €340,21

Produkthåndbøger:

Download FTB-900/FTB9500 Series - Precision Turbine Flowmeters
Download FLSC-64 - Pulse Amplifier
Download FLSC-62A - Signal Conditioner
Download FLSC-61 - 3-Wire Analog Transmitter
We noticed you are from the US. Visit your local site for regional offers and live support.