Cookies på Omegas websteder
Vi anvender cookies på vores websted. Disse cookies er afgørende for, at webstedet kan fungere korrekt.
Hvis du fortsætter uden at ændre dine indstillinger, antager vi, at du gerne vil modtage alle de cookies, der anvendes på dette websted. Du finder flere oplysninger om cookies ved at klikke her
Kurv  |  Kontakt  | 
GRATIS TELEFON (Kun Danmark. Alle opkald besvares på engelsk) 80 25 14 43
INTERNATIONAL(+45) 80 25 14 43
Layer N Banner

Current to Pressure (I/P) Converter


Current to Pressure (I/P) Converter - Order online | IP210

Current to Pressure (I/P) Converter - Order online

Se Alt Models Below

2 year warranty CE
  • Loop Power
  • Ideal for Pneumatic Control Systems
  • IP65 Sealed Case
  • Zero and Span Adjustments for Field Calibration
  • Rugged Zinc Cast Housing
  • Check our low cost IP211 I/P converter here
Ventiler, regulatorer og I/P-konvertere - Vis relaterede produkter


A "current to pressure" converter (I/P) converts an analog signal (4-20 mA) to a proportional linear pneumatic output (3-15 psig). Its purpose is to translate the analog output from a control system into a precise, repeatable pressure value to control pneumatic actuators/operators, pneumatic valves, dampers, vanes, etc. The IP210 is a loop powered instrument, which eliminates the need for an external power supply.

Accuracy: 0.5% FS, IP210. IP210A 1.5 and 2.3% (see spec sheet)
Supply Sensitivity: 0.025% span per % supply pressure change
Zero Adjustment: 5% FS
Span Adjustment: 20% FS
Operating Temp.: -5 to 160°F (-20 to 70°C)
Compensated Temp.: 15 to 140°F (-10 to 60°C)
Thermal Effects: Zero: 0.06% FS/°F Span: 0.06% FS/°F
Input Resistance: <300 Ohms
Media: Oil free clean dry air filtered to 25 µm
Recommended Supply Pressure: 25-30 psig (filtered air)
Max. Supply Pressure: 80 psig
Min. Supply Pressure: 10 psi above maximum output pressure
Air Consumption (leakage): 0.03 sfcm
Flow Rate: 10 sfcm typical
Response Time: Less than 0.5 seconds (10 to 90%step)
Failure Mode: Upon electrical failure, the signal pressure falls to bleed pressure.
Pressure Port: 1 /4 " NPTF
Electrical Conn.: DIN 43650 with screw terminals included
Housing: IP65 rated, Epoxy painted zinc die castings
Construction: Nitrile diaphragms, SS/nylon flapper, nozzle, and supply valve. Integral surface mounting bracket included.
Weight:3 lb (1.7 kg)
Til bestilling(Angiv modelnummer)
Vare nummer/Desc.
Quick Ship
Beholdning: 1 uge 
Current to pressure (I/P) converter with 2 wire 4-20 mA input and 3-60 psig output
Quick Ship
Beholdning: 1 uge 
Current to Pressure (I/P) Converter with 2 wire 4-20 mA input and 3-15 psig output
Quick Ship
Beholdning: 1 uge 
Current to Pressure (I/P) Converter with 2 wire 4-20 mA input and 6-30 psig output
Quick Ship
Beholdning: 1 uge 
Current to Pressure (I/P) Converter with 2 wire 4-20 mA input and 2-60 psig output
Quick Ship
Beholdning: 1 uge 
Current to Pressure (I/P) Converter
All amounts shown in DKK
Noter: IP210-X120 uses 3 wire 4-20 mA connection with external 12 to 24 volt power supply. All other models are 2 wire loop powered models.
We noticed you are from the US. Visit your local site for regional offers and live support.