Cookies på Omegas websteder
Vi anvender cookies på vores websted. Disse cookies er afgørende for, at webstedet kan fungere korrekt.
Hvis du fortsætter uden at ændre dine indstillinger, antager vi, at du gerne vil modtage alle de cookies, der anvendes på dette websted. Du finder flere oplysninger om cookies ved at klikke her
Kurv  |  Kontakt  | 
GRATIS TELEFON (Kun Danmark. Alle opkald besvares på engelsk) 80 25 14 43
INTERNATIONAL(+45) 80 25 14 43
Layer N Banner

Belastningsmåler/transmitter for lastcelle


Belastningsmåler/transmitter for lastcelle | TXDIN1600S

Belastningsmåler/transmitter for lastcelle

207,78 TXDIN1600S

  • Valgbare udgange i fuld skala for: 0-20 mA, 4-20 mA, 0-10 V ±10 V
  • Inputområde -7,6 til +7,6 mV/V maks. vælges af brugeren
  • Indbygget excitation af brokobling 5 VDC
  • Kontaktlukningsindgang til fjernstyret tara
  • Indgangsfilter på 0 til 20 sekunder
  • Skalering 2 til 6 punkter for ikke-lineært input
  • 10 eller 80 prøver/sekund
  • Nem skalering og opsætning via USB og gratis software
Tilbehør - Vis relaterede produkter


Omega's TXDIN1600S is a DIN rail mount transmitter for load cell or strain gauge inputs. Software available for free download allows the user to configure and scale the transmitter easily via a built-in mini USB port. Additionally, the user may read live process data through the software, allowing for offset and span calibration

Outputs can be either voltage, bipolar voltage or active/passive process current. The unit is powered by 10 to 48 Vdc or 10 to 32 Vac and is suitable for battery operation.

The high precision input stage of the device allows for a bridge excitation voltage of 5 Vdc to be used as opposed to the traditional 10V. This reduces the power requirement for the bridge supply and up to four bridges (load cells) may be connected to the input.

Advanced features such as remote tare, multi-point scaling, filtering and built-in bridge excitation make this transmitter suitable for a wide variety of applications.


      Full Range: -7.6 to +7.6 mv\V; -38 to +38 mV @ 5V excitation
      Type: Four Wire Ratiometric
      Drift: < ± 0.05 %
      Linearity: ± 0.01 %
      Update Rate: Selectable, 10 or 80 SPS (Samples per second)

      Voltage: 5 Volts DC ± 0.1 V @ 59 mA
      Bridge Impedance: Total 85 to 10000 Ω (operates with four 350 Ω load cells in parallel)

      Type: Remote volt free contact, up to 10 metres distance

      Current Source: Range 0 to 21.5 mA , Max Load 750 Ω
      Current Sink: Range 0 to 21.5 mA , Supply 10 to 30 V dc, Voltage effect 0.2 uA/V
      Accuracy: (mA Out/ 2000) or 5 uA which ever is the greater, Drift 1 uA/°C

      Range: 0 to 10.1 V or -10.1 to 10.1 V, Accuracy ± 5 mV
      Current Drive: ± 2 mA, Min load 5000 Ω @ 10 V

      Type: Independent “low” “High” front panel push buttons allow user to manually set low and high output points.

      Range: 10 to 48 VDC, 10 to 32 VAC Protected by internal 500 mA resettable fuse.
      Power: < 1 W Full Power

      Isolation: Supply to input to output 500 V dc.
      Indication: LED, Green when output -0.1 to 100.1 %, else red

      Type: USB 2.0
      Baud rate: 19,200 baud
      Equipment: PC running windows XP or later, USB cable.

      Calibration Scaling: 2 to 6 points signal against process
      Filter: 1 to 20 Seconds to reach 70 % of final value
      Tare: Remote set tare offset with programmable user set point.
      Active Calibration: Active Calibration against live load cell
      Process Units: 4 Characters
      Tag Number: 20 Characters
      Process Output: Process Output Range
      Signal Output: Select type, signal range
      Active scaling output: Set output process range against active sensor input
      Sensor Information: Model, sensitivity and balance

      Operating Ambient: -30 to +70 °C ; 10 to 90 %RH (non condensing)
      Storage Ambient: -30 to +70 °C ; 10 to 90 %RH (non condensing)
      Configuration Ambient: 10 to 30 °C
      Installation Enclosure: DIN Rail enclosure offering Protection >= IP65.

      CE: BS EN 61326

      Style: DIN 43880, Colour grey, material Polyimide 6.6
      Weight: < 70 grams
      Dimensions: 90 mm H x 15.5 mm W x 56.4 mm D
      Terminals: 2.5 mm Maximum

Til bestilling(Angiv modelnummer)

Andre har købt: Du kan klikke på dette ikon og få vist en liste over produkter, som andre har købt sammen med denne model.

Vare nummer/Desc.
Beholdning: På lager
Bridge Input Signal Conditioner / Transmitter, DIN Rail Mount.
Accessories (For details see Related Products links below)
Click to expand/minimize a list of what others bought with theLP-PS-1524
Kontakt salgsafdelingen    
DIN Rail mount power supply. 24 Vdc, 630mA output. 85-260 Vac input.
Click to expand/minimize a list of what others bought with theTX4-100
Beholdning: På lager
4-Core 0.2 mm² screened instrument cable with drain wire, 30 metres
All amounts shown in EUR
We noticed you are from the US. Visit your local site for regional offers and live support.